 |
MG-3D/M Multipurpose Grid, M3D/M3D-Sub/MILO/MILO 120/MILO
60
The MG-3D/M multipurpose grid accommodates multiple hanging configurations
or ground support for M3D and MILO, MILO 120 or MILO 60 high-power
curvilinear loudspeaker and M3D-Sub. MG-3D/M allows multipoint support
and bridles. Up to 24 MILO loudspeakers (or the equivalent weight
of MILOs and/or M3Ds and M3D-Subs) to be flown from the MG-3D/M.
Ground stacks of up to six MILOs (or the equivalent height of MILOs
and M3D-Subs) may be achieved.
MG-3D/M Grid and
Accessories Assembly Guide (6 MB PDF) |
 |
MLK-3D Link Kit, M3D/M3D-Sub
The MLK-3D link kit is required to attach an M3D and M3D-Sub loudspeaker
to the MG-3D/M multipurpose grid. The kit provides all necessary
links and pins.
MG-3D/M Grid and
Accessories Assembly Guide (6 MB PDF) |
 |
MLK-MILO Link Kit, MILO/MILO 120/MILO 60
The MLK-MILO link kit is required to attach a MILO, MILO 120 or
MILO 60 high-power curvilinear loudspeaker to the MG-3D/M multipurpose
grid. The kit provides all necessary links and pins.
MG-3D/M Grid and
Accessories Assembly Guide (6 MB PDF) |
 |
MTR-3D/M Transition Rails, M3D/M3D-Sub to MILO/MILO 120/MILO
60
The MTR-3D/M transition rail kit provides a simple and secure method
of attaching MILO, MILO 120 or MILO 60 high-power curvilinear loudspeakers
beneath or above M3D line array loudspeakers and/or M3D-Sub directional
subwoofers.
MG-3D/M Grid and
Accessories Assembly Guide (6 MB PDF) |
 |
MTB-2D/M Transition Bars, MILO to MG-2D to M2D
The MTB-2D/M transition bar facilitates connection of a MG-2D multipurpose
grid underneath a MILO array to allow simple and secure attachment
to M2D compact curvilinear array loudspeakers being used for near
and/or down fill applications.
MG-3D/M Grid and
Accessories Assembly Guide (6 MB PDF)
MG-2D Assembly Guide
(1 MB PDF) |
 |
MTF-3D Transition Frame, M3D/M3D-Sub/CQ-2/MSL-4
The MTF-3D provides a simple way to rig other Meyer Sound cabinets
beneath an M3D array for downfill applications. Three CQ-2 narrow
coverage main loudspeakersor three MSL-4 horn-loaded long-throw
loudspeakers may be suspended under an M3D/M3D-Sub array. The MTF-3D
transition frame requires that the under hung loudspeakers be fitted
with ring and stud rigging hardware.
M3D and M3D-Sub
QuickFly Rigging Manual (3.6 MB PDF) |
 |
MVE-MILO Vertical Extension Bars, MILO/MILO 60
For applications where the required splay angle is greater than
the full 5° capability of MILO’s rear AlignaLinks, the
MVE-MILO vertical extension bars can help. They are most useful
when high-frequency reflections from a specific area – such
as a balcony in a theatre or arena – must be minimized. The
MVE-MILO extension bars replace the front triangular AlignaLinks
on the top cabinet where the extended angle is required. The splay
angle can be increased by an additional 3°, 6°, or 9°.
This effectively provides up 12° (3° maximum of the rear
AlignaLinks plus 9° maximum of the MVE-MILO) splay angle.
MG-3D/M Grid and
Accessories Assembly Guide (6 MB PDF) |
 |
PBF-MILO Pull Back Frame, MILO/MILO 120/MILO 60
When acute array angles are desired, the PBF-MILO pull-back frame
can be fitted to the bottom of the lowest MILO, MILO 120 or MILO
60 high-power curvilinear loudspeaker in an array. The PBF-MILO
provides a pair of attachment points for a standard shackle linked
to a dedicated lift motor. (MTB-2D/M transition bar kit required.)
MG-3D/M Grid and
Accessories Assembly Guide (6 MB PDF) |
 |
MCF-MILO Caster Frame, MILO/MILO 120/MILO 60
This heavy-duty transport frame is easy to attach to a MILO, MILO
120 or MILO 60 high-power curvilinear loudspeaker. The frame is
built to take the weight of up to 24 MILO loudspeakers (or equivalent
weight of any combination of MILO, MILO 60, MILO 120 and the MILO
120-I insert) during rigging and tear down. For safety reasons,
we recommend that a maximum of four cabinets be stacked on the frame
during transit. The frame is also available with 2 by 5-inch HDPE
bumpers installed on all four sides, adding a 1-inch space between
stacks of loudspeakers when packed.
MG-3D/M Grid and
Accessories Assembly Guide (6 MB PDF) |
 |
MG-MICA Multipurpose Grid/MICA/600-HP
The MG-MICA multipurpose grid accommodates flown or ground stack configurations
for MICA compact high-power curvilinear array loudspeakers and 600-HP
compact high-power subwoofers (with optional MRK-600 rigging kit).
The MG-MICA allows multiple rigging points. In addition with the use
of the MGCP-MICA a single rigging point can be achieved. Up to 22
MICA loudspeakers (or the equivalent weight of any combination of
MICA and 600-HP cabinets) can be flown from the MG-MICA grid at a
7:1 safety factor, or 25 MICA loudspeakers at a 5:1 safety factor.
Certain restrictions apply, and this rating depends on grid angle
and the array’s center of gravity, which can be determined using
MAPP Online Pro’s rigging calculator.
MG-MICA Mulipurpose Grid Assembly Guide (9 MB PDF) |
 |
MGCP-MICA Center Point Pick-up, MICA/600-HP
The MGCP-MICA attaches directly to the MG-MICA grid, and allows
for a single point suspension without the need of bridles, especially
important in applications with low trim heights. The MGCP-MICA is
rated to fly up to 8 MICA loudspeakers (or the equivalent weight
of any combination of MICA and 600-HP cabinets) at a 7:1 safety
factor, or 11 MICA cabinets at a 5:1 safety factor.
MG-MICA Mulipurpose Grid Assembly Guide (9 MB PDF)
|
 |
MTF-MILO/MICA Transition Frame, MILO/MICA
The MTF-MILO/MICA transition grid allows MICA to be flown below
MILO for downfill applications. The compact frame creates minimal
space between MILO and MICA cabinets, for both aesthetic and acoustic
benefits. Up to 8 MICA may be flown from this frame at a 7:1 safety
factor, or 12 MICA cabinets at a 5:1 safety factor.
MG-MICA Mulipurpose Grid Assembly Guide (9 MB PDF)
|
 |
MDTL-MICA Downtilt Link, MICA/600-HP
The MDTL-MICA downtilt link adds a fixed amount of downtilt to
ground-stacked MICA loudspeakers, with an additional 6 degrees of
adjustment possible with the MICA’s rear GuideALinks. The
downtilt link connects between the MG-MICA grid or the top 600-HP
subwoofer and the lowest MICA loudspeaker.
MG-MICA Mulipurpose Grid Assembly Guide (9 MB PDF) |
 |
MCF-MICA Caster Frame, MICA/600-HP
The MCF-MICA caster frame allows up to four MICA cabinets or three
600-HP cabinets (with optional MRK-600 rigging kit) to be transported
fully rigged, and is dimensioned to provide tight packing in both
U.S. and European truck widths. To make MICA entirely road-ready,
durable nylon covers for up to four cabinets are also available.
MG-MICA Mulipurpose Grid Assembly Guide (9 MB PDF) |
 |
MG-M’elodie Multipurpose Grid
The MG-M’elodie is a lightweight, multipurpose grid that can fly up to 18 cabinets at a 7:1 safety ratio or be used for groundstacking. Also, up to six M’elodie cabinets can be groundstacked on the MG-M’elodie.
M'elodie Rigging
Assembly Guide (8.7 MB PDF) |
 |
MCF-M’elodie Caster Frame
The MCF-M’elodie caster frame allows up to five cabinets to be transported fully rigged, and is dimensioned for tight packing in both U.S. and European trucks.
M'elodie Rigging
Assembly Guide (8.7 MB PDF) |
 |
MUB-M'elodie U-Bracket
The MUB-M’elodie U-Bracket is a simple yet versatile mounting option that provides numerous tilt angles. The MUB-M'elodie is ideal for frontfill or under-balcony applications and supports up to three units.
|
 |
MTF-MICA/600/M’elodie Transition Frame
MTF-MICA/600/M’elodie Transition Frame is used to transition from MICA or 600-HP (fitted with MRF-600 frames) to M'elodie. (1 frame included)
M'elodie Rigging
Assembly Guide (8.7 MB PDF) |
 |
MG-2D Multipurpose Grid, M2D/M2D-Sub
The versatile MG-2D multipurpose grid allows the M2D and M2D-Sub
loudspeakers to be flown or ground stacked. MG-2D also provides
a transition from the bottom of an M3D/M3D-Sub array to an M2D/M2D-Sub
array. Up to 16 M2Ds (or a combination of M2Ds and M2D-Subs of comparable
weight) may be flown from single or multiple rigging points of appropriate
rating. When all the features and load capacity of the MG-2D is
not needed, small arrays of M2Ds can be flown using the MG-1D.
MG-2D Assembly
Guide (1 MB PDF) |
 |
MTK-2D Transition Kit, M3D/M3D Sub to MG-2D
To suspend M2D/M2D-Subs under an array of M3D/M3D-Subs a combination
of the MG-2D multipurpose grid and the MTK-2D transition kit must
be used. The MTK-2D provides required adjustable connecting bars
and pins.
MG-3D/M Grid and
Accessories Assembly Guide (6 MB PDF) |
 |
MTG-1D Top Grid, M1D/M1D-Sub
The MTG-1D provides multiple hanging configurations for M1D and
M1D-Sub arrays. MTG-1D provides for single- or multi-point support
and bridles. An adjustable rear extension frame provides flexibility
to keep the point load equal. Up to 16 M1Ds (or the equivalent weight
of M1D and M1D-Subs) may be suspended from single or multiple rigging
points of appropriate rating.
M1D Rigging
Grids Assembly Guide (2.1 MB PDF) |
 |
MG-1D Multipurpose Grid, M1D/M1D-Sub
The versatile MG-1D multipurpose grid allows M1D/M1D-Sub loudspeakers
to be flown or ground stacked. MG-1D also provides a transition
from the bottom of an M2D/M2D-Sub array to an M1D/M1D-Sub array.
Up to 12 M1Ds (or the equivalent weight of M1Ds and M1D-Subs) may
be suspended from single or multiple rigging points of appropriate
rating. In addition the MD-1D can be used to fly M2Ds and/or M2D-Subs.
Up to seven M2Ds (or the equivalent weight of any combination of
M2Ds and M2D-Subs) can be flown from the MG-1D grid at a 7:1 safety
factor, or 10 M2Ds at a 5:1 safety factor.
M1D Rigging
Grids Assembly Guide (2.1 MB PDF) |
 |
MUB-1D Mounting U-Bracket, M1D
Supports or suspends multiple M1Ds in a floor or ceiling mounted
configuration. Numerous tilt angles are possible.
M1D Rigging
Grids Assembly Guide (2.1 MB PDF) |
